... e-shop s autodíly!

OE 569020
CHEVROLET

Brzdový kotouč

CHEVROLET569020

Číslo OE, nebo také OE kód či OEM kód - znamená číslo originálního vybavení (Original Equipment) - tedy číslo kompletních součástí nebo podskupin, které byly původně namontovány na vozidlo. OE číslo je zaměnitelné s termínem Originální číslo.

Náhradní díly kompatibilní s OE čísly


  • VAICO Brzdový kotouč - 236 mm VAC V40-40006

    zvětšitVAICO Brzdový kotouč - 236 mm ‐ VAC V40-40006
    379,-ve skladu
    Montovaná strana: přední osaSrovnávací průměr: 236Výška náboje brzdového kotouče [mm]: 28,2Ráfek, počet děr: 4Výška [mm]: 41Typ brzdového kotouče: plnýSíla brzdového kotouče [mm]: 12,7Minimální tloušťka [mm]: 9,7Vnější průměr [mm]: 236Centrovací průměr [mm]: 60Kruhový vývrt ∅ [mm]: 100EAN:040460012065424046001206542CITROËN90272326OPEL00569 013 (00569013)00569 020 (00569020)00569 030 (00569030)05 69 013 (0569013)05 69 020 (0569020)05 69 030 (0569030)5 69 020 (569020)5 69 030 (569030)569 013 (569013)56901390 008 005 (90008005)90 008 031 (90008031)900080059000803191 95 981 (9195981)93 182 290 (93182290)93182290VAUXHALL00919598109000800509195981093182290093182311569030900080059000803190111242919598193182311CHEVROLET569020569030GENERAL MOTORS00919598109000800509195981093182290PONTIAC90111242Konkurenční kódy 
    Všeobecné informaceProducts supplied by us are without exception intended for
    the designated use.
    Please note that our products are usually delivered without
    installation instructions.
    Installation may only be carried out by trained specialist
    personnel.
    There is no guarantee for inappropriate, improper or
    unintended use.
    In the warranty, we always make a distinction between wear
    parts and vehicle parts. All wear parts are subject to a
    reduced warranty period and a maximum mileage.
    Brake components such as brake disks, brake pads, etc.
    maximum of 1000 km (break-in period). Therefore, warranty
    claims for brake parts are only reviewed with an
    installation invoice and a record of the wheel hub run-out
    measurement, including photos.
    For brake disks and brake pads, the break-in requirements
    specified by the vehicle manufacturer must be observed.
    When replacing brakes, the chassis components must always be
    checked with regard to clearance and the wheel hub with
    regard to wobble, and the appropriate documentation must be
    produced.
    If the vehicle is no longer in its original condition due to
    tuning work such as wheel accessories and tracking plates,
    the entitlement to make warranty claims is lost due to
    third-party work. The same warranty claims are lost if the
    vehicle is used for motor sports or similar events.

Logo Heuréka

Tento e-shop měl za posledních 90 dní tisíce spokojených zákazníků.


Logo Zboží.cz

Zde prezentovaná data, zejména celá databáze, nesmějí být kopírována. Je zakázáno data nebo celou databázi bez předchozího písemného svolení od společnosti TecAlliance kopírovat a distribuovat a/nebo toto jednání umožnit třetím osobám. Porušení zakládá neoprávněný zásah do autorského práva a bude stíháno.